Molle Ottoman Storage Bed Frame

1. Position the Right (R) and Left (L) Side Rails with the correct orientation, as indicated.
2. Attach Bracket Bases (8) with CSK M4x32 screws (S), secure them to the inner sides of each rail, aligning with the pre-drilled holes. Ensure the brackets face the correct direction towards the headboard.

Important: Part 8 (Bracket Base) must be attached before installing Part 7 (Pump Mounting Bracket) to ensure proper assembly.

1. Attach Pump Mounting Brackets (7), position the brackets on the Right (R) and Left (L) Side Rails as shown.
2. Secure using JCBC M6 X 40 screws (B), M6 Spring Washers (E), and M6 Flat Washers (F) through the pre-drilled holes in Bracket Base (8).
3. Use the M4 Allen Key (K) to tighten the screws securely.

Caution: Tighten the screw at the position of the long hole as shown

1. Lay out the Headboard (1), Footboard (2), and Side Rails (R & L).
2. Insert the white nails (R) on the unfinished side of all the parts, ensuring they are not too close to the edges.
3. Verify the nails are secured and correctly positioned as shown in the detail view.

Tip: Position nails centrally to avoid weakening the edges

1. Arrange the Headboard (1), Footboard (2), and Side Rails (R & L) to form the bed frame.
2. Secure the Angle Brackets using the provided JCBC M6 X 40 screws (Q).
3. Tighten the screws using the M5 Allen Key (L) to ensure a firm connection.

1. Place the Black Woven (18) on top of the bed frame, ensuring it aligns with the edges.
2. Attach the woven base to the frame using the Velcro strips provided, ensuring a firm and even fit.

1. Align the brackets at the designated locations inside the frame, as shown in the illustration.
2. Use JCBC M6 X 20 screws (A), M6 Spring Washers (E), and M6 Flat Washers (F) to attach the brackets.
3. Tighten the screws using the M4 Allen Key (K) for a secure fit.

1. Align the stopper with the designated slot on the Main Frame (10).
2. Slide it securely into place, ensuring it fits firmly onto the frame and does not move freely.

1. Position the Main Frame - Front and End (10) and Side Frames (11) at the headboard and footboard ends.
2. Fix the hole for the bolt between the first and second pair of holder holes to the headboard end.
3. Fix the hole for the bolt between the second and third pair of holder holes to the footboard end.

1. Attach the Rubber Corner Connectors (14), position the connectors at each corner where the Main Frames (10) and Side Frames (11) meet.
2. Firmly press the rubber connectors into place, ensuring they lock the frame sections together.

1. Position the Frame Lifter (O) at the designated location on the rail.
2. Install the Support Leg (15), secure the leg in place beneath the frame lifter. Use JCBC M6 X 50 screws (C), M6 Spring Washers (E), M6 Flat Washers (F), and M6 Hex Nuts (G) to fasten to the rail. 
3. Tighten using the M4 Allen Key (K) and M6 Spanner (M).
4. Place and rotate the Adjuster (P) to ensure the support leg is stable and properly aligned.

1. Align the Center Rail (12) with the pre-drilled holes in the Main Frame (10).
2. Secure with hardware, use JCBB M8 X 50 screws (D), M8 Spring Washers (H), M8 Flat Washers (I), and M8 Hex Nuts (J). Tighten using the M5 Allen Key (L) and M8 Spanner (N).

1. Position the Metal Corner Brackets (13), align the brackets at the designated locations on the frame.
2. Secure with hardware, use JCBC M6 X 50 screws (C), M6 Spring Washers (E), M6 Flat Washers (F), and M6 Hex Nuts (G). Tighten using the M4 Allen Key (K) and M6 Spanner (M).

1. Attach the Slat End Holders (4) to the Slats (6), then secure them to the Side Rails.
2. Attach the Slat Middle Holders (5) to the Slats (6), then secure them to the Center Rail (12).
3. Position each Slat (6) over the designated slots and press them into place.
4. Secure the Slats (6) by firmly pushing them into the End Holders (4) and Middle Holders (5) to lock them in position.

Number of slats for each size:

• Double: 24 Slats / 24 Single Plastic Caps / 12 Double Plastic Caps.
• King: 26 Slats / 26 Single Plastic Caps / 13 Double Plastic Caps

Align the Fabric Loop (O), position the loop at the designated location on the Center Rail (12). Check that the loop is firmly in place and ready for use.

Note: The Frame Lifter (O) is a fabric loop, not a rigid part.

1. Align the Gas Springs (16), position the gas springs at the designated attachment points on the bed frame.
2. Attach each gas spring using the provided bolts and tighten them with the M6 Spanner (M).
3. Ensure both gas springs are securely fixed and aligned correctly for smooth operation.

Important: Do not overtighten the bolts to allow proper movement of the gas springs.

1. Align the gas springs with the designated mounting points on the bed frame.
2. Secure with hardware, use JCBB M8 X 50 screws (D), M8 Spring Washers (H), M8 Flat Washers (I), and M8 Hex Nuts (J). Tighten using the M5 Allen Key (L) and M8 Spanner (N).
3. Ensure the gas springs are securely attached and can move smoothly to support the lifting mechanism.