Lucia Off White Ottoman Bed Frame

1. Attach the Corner Hook - Left (G) and Corner Hook - Right (H) to both the Side Rail - Left and Side Rail - Right using Bolt (A), Spring Washer (E), and Flat Washer (F).
2. Ensure the hooks are securely fastened at both ends of each side rail.

1. To attach the Headboard (1) and Footboard (2) to the Side Rails first attach a Bolt (A), Spring Washer (E), and Flat Washer (F).
2. Ensure each bolt is tightened securely, maintaining a 10mm gap as shown.

1. Attach the Side Rail - Left (3) and Side Rail - Right (4) to the Headboard (1) and Footboard (2) using the Corner Hooks.
2. Ensure the bolts are tightened to a 90% tightness, maintaining a 10mm gap as shown.
3. Once hooked, tighten the bolts.

1. Attach the 'L' Shape Bracket (14) to the Headboard (1) and Footboard (2) using Bolt (A), Spring Washer (E), and Flat Washer (F).
2. Ensure the brackets are securely fastened to provide additional support to the frame.

1. Attach the Angled Corner Bracket (9) to the junction of the Side Rail - Left (3), Side Rail - Right (4), and Footboard (2)
2. Use Bolt (A), Spring Washer (E), and Flat Washer (F) and tighten.
3. Ensure the brackets are aligned correctly to maintain a rectangular frame shape, as shown in the correct alignment diagram.

1. Position the Gas-lift Mechanism LH (5) and RH (6) together with the Spacer Rails (7) inside the bed frame, along the inner Side Rails.
2. Place the Spacer Rails (7) between the bed frame and the lift mechanism brackets, ensuring they sit underneath the gas-lift arms.
3. Align the lower sections of the lift arms and the Spacer Rails with the pre-drilled holes on the Side Rail LH (3) and RH (4).
4. Secure each bracket with 4 × Bolt (B) on each side.
5. Tighten all bolts using the Allen Key (M) to ensure the lift arms and Spacer Rails are securely attached.

1. Attach the Side Rail Cross Bar (8) between the Side Rail - Left (3) and Side Rail - Right (4).
2. Use Bolt (A), Spring Washer (E), and Flat Washer (F) to secure the cross bar.
3. Ensure the cross bar is aligned correctly and all bolts are tightened securely for stability.

Place the Fabric Base Cover (11) inside the bed frame, ensuring it lies flat and covers the entire base area.

Adjust as necessary to fit securely within the frame.

1. Unfold the Metal Slat Frame (15).
2. Align the Metal Connection Plates (K) with the pre-drilled holes on the slat frame.
3. Secure the connection plates using Bolt (A) and tighten with the Allen Key (I).
4. Attach the Mattress Stopper (12) to the end of the slat frame by inserting it into the designated slots.
5. Finish by tying the Fabric Handle Strap (10) on the opposite side.
6. Ensure all components are securely fastened and aligned properly.

1. Slide the Gas-lift Piston Stem (X) onto the Axle (Y).

2. Place the Flanged Lock-Nut (D) onto the stem and tighten with the Spanner (J).

   • Do not over-tighten, leave a small gap so the stem can move freely.

3. Connect the Gas-lift Piston (13) to the pre-installed Gas-lift Mechanism on both sides of the bed frame.

4. Check that the pistons move freely and that all components are aligned and securely fastened.

1. Align the Metal Slat Frame (15) with the Gas-lift Mechanism on both sides of the bed.
2. Loosely fit three bolt sets (Bolt C, Flat Washer F, Spring Washer E, and Flanged Lock-Nut D) on each side.
3. Carefully hold the frame down and adjust so there are even gaps on both sides.
4. Once aligned, tighten all bolts 100% using the Allen Key (I) and Spanner (J).
5. Verify that the frame is securely attached and all components are properly fastened.

1. Slide the stem of the Gas-lift Piston (13) (X) onto the Axle (Y) on the underside of the Metal Slat Frame (15).
2. Fit the Flanged Lock-Nut (D) and tighten it using the Spanner (J), do not over-tighten.
3. Repeat this process for both pistons.

Important: A small gap must be left between the piston stem and the bracket to ensure the piston can move freely. Refer to the diagram to confirm correct spacing.

1. Storage Area Safety

• Ensure the ottoman is fully open before accessing the storage space.

• Avoid reaching through the hinge area to prevent injury.

• Keep children and pets away from the bed when it is open.

• Do not stand or climb inside the internal storage compartment.

• Regularly inspect the bed mechanism to ensure it is functioning safely and smoothly.

2. Operating Instructions

• The gas-lift mechanism is intended for adult use only. It is not suitable for users under 12 years old.

• Always lift and lower the ottoman with the mattress in place, using the fabric hand strap (13) to raise and lower the base.

• Keep hands and body clear of the lifting mechanism during operation to avoid entrapment.

Note: Be mindful of what you store under the bed. Items such as suitcases or boxes must not touch the underside of the slat frame, as this may cause damage.

Maximum recommended storage height is 225mm.