SUMMIT⁶ Assembly Manual

Refer to SUMMIT⁴ Assembly Manual.

Refer to SUMMIT⁴ Assembly Manual.

Refer to SUMMIT⁴ Assembly Manual.

Refer to SUMMIT⁴ Assembly Manual.

Refer to SUMMIT⁴ Assembly Manual.

• Connect GEN4_DOCK_2.X-G4_MASTER to GEN4_DOCK_2.1-G4_SLAVE units.

• Connect each GEN4_DOCKBOX to the corresponding GEN4_ELEKTRO_FAN SLAVE (E0815).

• Connect the LAN cable (RJ45) and the power cord to the GEN4_POWERBOX.

• After testing the connection, unplug the power cord.

Parts used:

• Power cord | E0508 | 1×

• LAN cable (RJ45) | — | 1×

• GEN4_ELEKTRO_FAN SLAVE | E0815 | 2×

• Position the long external panel rails around the top and sides of the pod structure.
• Align each rail with the designated edges of the roof and side frames.

Parts used:

• External panel rails | — | 4×

• Secure the previously placed external panel rails to the top structure using screws.
• Tighten all screws from the top, as shown in the floor top view.

Parts used:

• M6×40 bolt | T0397 | 8×

• Align the base plates of the table legs with the designated holes in the floor.

• Fasten each leg securely using screws.

Parts used:

• 6×25 screw | T0305 | 10×

• Insert the rectangular cover plates (P1274) over the base of each table leg.

• Ensure they are aligned and lie flat on the floor.

Parts used:

• Cover plate | P1274 | 4×

• Place the floor insulation panels inside the pod as shown.

• Ensure correct placement: panels marked 1.1.4-SUG4 go on the left side, and 1.1.5-SUG4 panels cover the right and center sections.

Parts used:

• Floor insulation panel | 1.1.4-SUG4 | 2×

• Floor insulation panel | 1.1.5-SUG4 | 3×

popsat v textu vylomení záslepek

• If a table is being installed, use a utility knife to cut openings in the carpet for the table supports.

• The position of these openings is indicated by perforations on the carpet.

• Place the carpet into position.

Parts used:

• carpet | 2×

• Place the tabletop onto the two vertical table legs.
• Align the holes underneath the tabletop with the mounting holes on the top of the legs.
• Fasten using the provided screws.

Parts used:

• M6×16 mm flat head bolt | T0322 | 8×

• Route the GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600mm (E0816) along the indicated side of the structure as shown in the diagram.

Parts used:

• GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600mm | E0816 | 1×

• Position the labeled interior panels (as per the diagram) in their designated locations inside the structure.

Parts used:

• 7.1-SUG4 | 2×

• 7.1-SU6,8G4 | 1×

• 7.2-SUG4 | 7×

• 7.2-SU6,8G4 | 4×

• 7.3-SUG4 | 1×

• 7.4-SUG4 | 4×

• 7.4-SU6,8G4 | 2×

• 7.5-SUG4 | 3×

• 7.5-SU6,8G4 | 1×

• 7.7-SUG4 | 4×

• 7.7-SU6,8G4 | 2×

1. Unpack the Components: Carefully open the packaging and identify the display unit (P1013)

2. Disassemble the Housing: Using a screwdriver with a Torx bit, remove the rear frame from the display unit to prepare it for mounting.

3. Feed the Cables: Locate the cutout in the upholstered internal panel. Gently pull all display cables through the hole from the front (upholstered side) to the back.

   Note: Ensure the cables are oriented upwards as shown in the diagram.

4. Seat the Display: Insert the display unit into the cutout on the upholstered side of the panel until it sits flush against the surface.

5. Mount the Rear Frame: From the back of the panel, align the rear frame (P1013) with the back of the display unit.

6. Fasten the Bolts: Insert the provided bolts through the frame and into the display housing. Tighten them securely to sandwich the upholstered panel between the display and the rear frame.

Parts used:

• Interior panel | 7.3-SUG4 | 1×

• Display | P1013 | 1×

• Insert pins into the pre‑drilled holes of the bottommost panels.

• Install a minimum of four clip connectors into the external panel.

• Fit the adjacent panels as shown in the illustration. Begin installation from the bottom and move upward sequentially.

Parts used:

• external panel | 8.1-SP, CH2, SG4 | 24×
• clip connector | T0122 | 96×
• 8×30 mm dowel pin | T0122 | 12x

• Route the GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600mm (E0816) as shown.
• Connect the cable to the occupancy light.
• Secure the occupancy light (E053) to the frame with the provided screws.

Parts used:

• 3x30 | T0136 | 2×

• Place the hinge covers over the hinges on the door frame as shown.
• Secure each cover with screws.

Parts used:

• M4×10 | 12×

• Apply double-sided tape along the back of the ledge (K0493).
• Stick the ledge to the indicated position on the frame.

Parts used:

• Ledge | K0493 | 1×

• Apply double-sided tape along the back of the ledge (K0494).
• Stick the ledge to the indicated position on the frame.

Parts used:

• Ledge | K0494 | 1×
• Double-sided tape (quantity as needed)

• Connect the power supply cord to the powerbox.

Parts used:

• Power cord | (reference code not specified) | 1×

• Position the cover (K0487) over the power cord and secure it in place.

Parts used:

• Cord cover | K0487 | 1×

• Place the internal panel (7.1-SUG4) over the power cord section and secure in position.

Parts used:

• Internal panel | 7.1-SUG4 | 1×