CHAT² is the ideal pod for private conversations and quick meetings, free from distractions. Designed for two, it combines exceptional sound isolation with modern comfort, ensuring seamless and confidential communication in any workspace.
Use the marked holes in the picture to insert the screws (T0509). If your order includes wheels (V0181), attach them to the same holes using screws M10×25 mm (T0509).
Parts used:
wheel | V0181 | 8×
M10×25 mm screw | T0509 | 8×
2. Install Leveling Feet
Keep the 1.1.1-CHG4 floor panel flipped upside down (bottom side up).
Insert one levelling foot (V0050) into each of the 8 marked holes on the underside of the floor
panels.
Using a Phillips head screwdriver, partially screw in the standing feet. Leave approximately 20 mm of clearance to allow for future adjustments—do not fully tighten them at this stage.
Parts used:
M10×55 mm adjustable foot | V0050 | 8×
3. Route Cables Through the Hole
Lay the GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600 mm (E0816), LAN cable (RJ45), and power cord through the hole in the floor panel. Follow the marked path shown in the bottom view, ensuring the cables are not pinched.
Use a laser level and L-angle (or a spirit level) to level the floor. Adjust the height of the standing feet using a Philips head bit.
Dock
4. Remove Revision Doors
Remove the Revision Doors (K0487) from the docks.
Parts used:
Revision door K0487 | 2×
5. Mount Dock on the Floor Panel
Insert 8×30 mm dowel pins (T0122) into the predrilled holes on the floor panel to maintain proper alignment.
Position one dock at a time in place.
Pull the power cord, PIR sensor cable, and signalization cable through the opening in the dock panel for later connection.
Parts used:
8×30 mm dowel pin | T0122 | 5×
6. Secure the Dock to the Floor Panel
Insert M8×45 mm hex‑head bolts (T0204) through the inner mounting holes.
Place a washer (T0198) underneath each bolt head.
Tighten securely until the bolt and washer are seated flush with the panel surface.
Use the cut-outs on the exterior side of the dock panels to draw them tightly together.
Insert an M6 × 30 mm bolt through the aligned holes. Place a washer under the bolt head and thread an M6 flange nut onto the bolt from the opposite side.
Tighten all bolts firmly to hold the connector in place.
Parts used:
M8×45 mm hex head | T0204 | 6×
washer 8.4×24×2.0 mm | T0198 | 11×
M6×30 mm bolt | T0511 | 5×
M6 flange nut | T0514 | 5×
Panel
7. Mount Wall Panel to the Floor
Insert two dowel pins (T0122) into the predrilled holes in the floor panel.
Align the panel with the pre-drilled holes on the floor panel (1.1.1-CHG4) and the dock frame.
Secure the bottom of the panel using M8×45 mm hex head bolts (T0204) and washers (T0198) through the mounting points.
Parts used:
M8×45 mm hex head | T0204 | 4×
washer 8.4×24×2.0 mm | T0198 | 4×
8×30 mm dowel pin | T0122 | 2×
Roof
8. Attach Roof
Identify part 4.1-CHG4, the roof panel.
Insert eight dowel pins (T0122) into the designated guide holes along the top edges of the wall panels.
Carefully lower the roof panel onto the structure, aligning the dowel pins with the corresponding holes on the underside of the roof.
Ensure the panel sits flush and is properly seated before proceeding to fasten.
Parts used:
8×30 mm dowel pin | T0122 | 8×
9. Secure Roof
Insert M6×60 mm flat head bolts (T0510) through the pre-drilled holes in the roof panel (4.1-CHG4) into the wall panels.
Place washers (T0198) under each bolt head.
Tighten each bolt evenly and securely, but avoid over-tightening to prevent damage to the panels.
Parts used:
M6×60 mm flat head bolt | T0510 | 8×
Washer 8.4×24×2.0 mm | T0198 | 8×
Rear Frame
10. Attach Threaded Rod to Rear Frame
Place the M6×90 mm threaded rod (T0547) into the 6.1 CHG4 and M6×50 mm threaded rod (T0515) into the 6.1-G4, 6.2-G4 and 6.1-CHG4.
Parts used:
M6×50 mm threaded rod | T0515 | 15×
M6×90 mm threaded rod | T0547 | 5×
11. Attach Rear Frame to the Pod
Insert D8×50×22 mm dowels (T0536) into the oval holes
Align the horizontal frame 6.1-CHG4 and 6.2-CHG4 with the mounting slots at the rear edge of the floor panel.
Place washers (T0198) and M6 flange nuts (T0514) on the threaded rod in the floor cutouts.
Ensure the frame is aligned correctly before tightening properly.
Parts used:
D8×50×22 mm spacer | T0536 | 6×
washer 8.4×24×2.0 mm | T0198 | 5×
M6 flange nut | T0514 | 5×
12. Check Gap and Insert Spacer if Necessary
If there is a gap between the frame and the floor, insert a spacer into the groove.
13. Attach Rear Frame to the Wall Panel
Place the two vertical frames, 6.2-G4 and 15.05-G4, in their designated positions.
Secure each frame by inserting a washer (T0198) and tightening an M6 flange nut (T0514) onto the threaded rod in the slot openings.
Ensure the frames are properly aligned before fully tightening the nuts.
Parts used:
Flange nut M6 | T0514 | 5×
Washer 8.4×24×2.0 mm | T0198 | 5×
14. Install Rear Glass into the Frame
Clean the edge of the glass with the glass cleaner to remove any dust or grease.
Carefully apply double-sided gel tape along the cleaned edge. Do not remove the protective foil from the tape at this stage.
Insert the glasses (6.3-CHG4) into the groove in the Rear frame.
Use suction cups to secure the second glass.
Parts used:
double-sided gel tape | S0105 | 2×
15. Install Rear Glass into the Frame
Clean the edge of the glass with the glass cleaner to remove any dust or grease.
Carefully apply double-sided gel tape along the cleaned edge. Do not remove the protective foil from the tape at this stage.
Insert the glasses (6.3-CHG4) into the groove in the Rear frame.
Parts used:
double-sided gel tape | S0105 | 1×
16. Secure Glass Panels with Double-sided Tape
Align the glass with the groove on the side of the panel. Remove the protective film from the double-sided tape and use suction cups to pull the glass together.
17. Attach Rear Frame to the Dock
Locate part 15.04-G4 (front right vertical profile) and 6.1-G4 (front left vertical profile).
Align each profile with the corresponding front frame posts.
Secure Rear frame using M6 flange nuts (T0514) and washers (T0198).
Parts used:
flange nut M6 | T0514 | 10×
washer 8.4×24×2.0 mm | T0198 | 10×
18. Attach Rear Frame to the Roof
Identify parts 6.1-CHG4 and 6.2-CHG4.
Place the frame at the top of the rear frame, aligning them with the corresponding holes.
Secure the profile using M6 flange nuts (T0514) and washers (T0198) as indicated.
Parts used:
flange nut M6 | T0514 | 5×
washer 8.4×24×2.0 mm | T0198 | 5×
Front Frame
19. Attach the Threaded Rod to Front Frame
Place the M6×90 mm threaded rod (T0547) into 2x 5.5-CHG4, 1x 5.6-CHG4 Frame.
Insert M6×50 mm threaded rod (T0515) into the 5.2-CH,SUG4, 5.3-CH,SUG4, 5.4-F,CHG4 and 5.1-FG4, 2x 5.5-CHG4, 1x 5.6-CHG4 Frame.
Parts used:
M6×50 mm bolt | T0515 | 21×
M6×90 mm bolt | T0547 | 7×
20. Attach Front Frame to the Floor Panel
Insert D8×50×22 mm dowels (T0536) into the oval holes
Align the horizontal frame 5.5-CHG4 , 5.6-CHG4 and 5.7-CHG4 with the mounting slots at the rear edge of the floor panel.
Place washers (T0198) and M6 flange nuts (T0514) on the threaded rod in the floor cutouts.
Ensure the frame is aligned correctly before tightening properly.
Parts used:
dowel pin D8×50×22 mm | T0536 | 6×
flange nut M6 | T0514 | 7×
washer 8.4×24×2.0 mm | T0198 | 7×
21. Attach Door and Roof Front Frame
Position the frame 5.3-CH,SUG4, 5.4-F,CHG4 and 5.8-CHG4 at the front of the frame as shown.
Secure the profiles using flange nuts and washers from the hardware list.
Parts used:
flange nut M6 | T0514 | 4×
washer 8.4×24×2.0 mm | T0198 | 4×
22. Attach Front Frame to the Roof
Insert frame 5.6-CHG4 horizontally as shown.
Align the holes in the frame with the Roof part.
Secure in place using the specified hardware.
Parts used:
flange nut M6 | T0514 | 3×
washer 8.4×24×2.0 mm | T0198 | 3×
23. Install Rear Glass into the Frame
Insert glass panels 5.9-CHG4 and 5.10-CHG4 from below into the left and right front frame grooves.
Parts used:
glass | 5.9-CHG4 | 1×
glass | 5.10-CHG4 | 1×
24. Attach Front Frame to Wall Panel and Dock
Place the vertical frame 5.1-F,CHG4, 5.2-CH,SUG4, and 6.7-G4 into their respective positions.
Secure each frame by inserting a washer (T0198) and tightening an M6 flange nut (T0514) onto the threaded rod in the slot openings.
Ensure the frames are properly aligned before fully tightening the nuts.
Parts used:
Frame | 5.1-F,CHG4 | 1×
Frame | 5.2-CH,SUG4 | 1×
Frame | 6.7-G4 | 1×
Frame | 15.04-G4 | 1×
flange nut M6 | T0514 | 10×
washer 8.4×24×2.0 mm | T0198 | 10×
25. Attach Front Frame to the Roof
Insert both 5.5-CHG4 horizontal frames, in their designated positions.
Secure each frame by inserting a washer (T0198) and tightening an M6 flange nut (T0514) onto the threaded rod in the slot openings.
Ensure the frames are properly aligned before fully tightening the nuts.
Parts used:
frame | 5.5-CHG4 | 2×
flange nut M6 | T0514 | 4×
washer 8.4×24×2.0 mm | T0198 | 4×
26. Secure the Rear frame and the Front frame
Insert M4×45 mm screws through the frame as shown to fasten the structure.
Parts used:
M4×45 mm screw | T0535 | 8×
Door
27. Fasten Frame to the Glass
Place the glass 5.11-F,CH,SUG4 on the working stand.
Insert the plastic insert (O0433) into the countersunk holes in the glass, and secure the frame to the glass using M8×25 mm screws (T0512).
Parts used:
Reinforcement bar | 5.8-G4 | 1×
M8×25 mm screw | T0512 | 6×
Insert | O0433 | 6×
28. Mount Door Hinges
Attach hinges (V0002) into the recess use M4×30 mm screws to secure the position.
Repeat for all 3 positions as shown.
Parts used:
Sliding bracket | V0002 | 3×
M4×30 mm screw | T0070 | 6×
29. Secure the Door in the Frame
Place the door into the recesses in the frame and secure it with screws M4×30 mm (T0070).
Parts used:
M4×30 mm screw | T0070 | 6×
30. Install Handle
Align the two parts of the handle on either side of the hole in the glass.
Insert the enclosed M6×120 mm screw through the hole and fasten the handle parts using a 4 mm hex key.
Place the plastic spacer between the screw and the glass to prevent direct contact.
Tighten the screw securely, ensuring the handle is firmly attached without over-tightening.
Parts used:
M6×120 mm bolt | T0530 | 2×
6.2×10×10 mm spacer | T0097 | 2×
Speakers
31. Install Speakers
Position the speaker modules in the predrilled ceiling holes.
Secure each speaker with two M4x10 screws (T0499).
Plug the corresponding cable SPEAKERS 8Ω 5W (2 pin) to the speakers.
Parts used:
M4×25 mm screw | T0435 | 4×
Light
32. Install Light
Connect the PIR sensor cable (RJ11) and the dual light cable (6 pin).
Position and secure the light panel to the ceiling using screws.
Parts used:
M4×10 mm screw | T0499 | 4×
Electro Connection
33. Complete Electrical Wiring
Connect GEN4_DOCK_2.X-G4_MASTER to GEN4_DOCK_2.1-G4_SLAVE units.
Connect each GEN4_DOCKBOX to the corresponding GEN4_ELEKTRO_FAN SLAVE (E0815).
Connect the LAN cable (RJ45) and the power cord to the GEN4_POWERBOX.
After testing the connection, unplug the power cord.
Parts used:
power cord | E0508 | 1×
electro fan slave | E0815 | 1×
External Panels
34. Attach Eternal Panels
Install the upper panels 8.3-SUG4 by aligning them with the edge of the frame and the screw holes.
Prepare the lower panels 8.2-SUG4 by positioning them underneath the frame. You may use spacers or supports to make fastening easier.
Parts used:
external trim panel | 8.2-CHG4 | 2×
external trim panel | 8.3-CHG4 | 2×
35. Fix the External Panels
Secure the previously placed external panels using M6×40 mm screws (T0397).
Parts used:
M6×40 mm screw | T0397 | 12×
Table
36. Attach Table Supports to the Floor
Align the base of the table leg with the designated cutout in the floor.
Fasten leg securely using screws.
Parts used:
screw 6×25 mm | T0305 | 5×
37. Place Floor Covers
Insert the floor cover (P1274) into the unused cutout.
Ensure it is properly aligned and lie flat on the floor.
Parts used:
floor cover | T0103 | 1×
Ledge
38. Install Ledge
Apply double-sided tape along the back of the ledge (K0406).
Stick the ledge to the indicated position on the frame.
Parts used:
ledge | K0406 | 1×
double-sided tape | B0007 | 1×
Floor Isolation
39. Place Floor Isolation Panels inside the Pod
Place the floor insulation panels inside the pod as shown.
Ensure correct placement: panels marked 1.1.3-CHG4 go on the left side, and 1.1.4-CHG4 panels cover the right and center sections.
Parts used:
floor insulation panel | P1270 | 1×
floor insulation panel | P1271 | 1×
40. Insert Blind Plug into the Opening
Insert the insulation blind plug P1269 into the corresponding openings.
Parts used:
blind plug | P1269 | 1x/2×
Carpet
41. Lay Carpet on the Floor
Place the carpet into position.
If a table is being installed, use a utility knife to cut openings in the carpet for the table legs.
The position of these openings is indicated by perforations on the carpet.
Parts used:
carpet | O0448 | 1×
Table
42. Attach Tabletop to the Table Leg
Place the tabletop onto the table leg.
Align the holes underneath the tabletop with the mounting holes on the leg.
Fasten using the provided screws.
Parts used:
6×16 mm screw | T0322 | 4×
Occupancy Light Cable
43. Route the Occupancy Light Cable through the Frame
Route the GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600 mm (E0816) in the groove as shown.
Parts used:
occupancy signalization cable 4600 mm | E0816 | 1×
Interior Panels
44. Insert Display into the Interior Panel
Place the display into the interior panel cutout from the front.
Route the cables through the cutout.
Secure display from behind using the plastic cover and screws.
45. Install Interior Wall and Ceiling Panels
Position the labeled interior panels (as per the diagram) in their designated locations inside the accoustic pod.
Exterior Panels
46. Install External panels
Insert pins into the pre‑drilled holes of the bottommost panels.
Install a minimum of four clip connectors into the external panel.
Fit the adjacent panels as shown in the illustration. Begin installation from the bottom and move upward sequentially.
Parts used:
external panel | 8.1-SP, CH2, SG4 | 8×
clip connector | T0122 | 32×
dowel pin |
Occupancy Light
47. Install Occupancy Light
Route the GEN4_ELEKTRO_CABLE OCCUPANCY SIGNALIZATION 4600 mm (E0816) as shown.
Connect the cable to the occupancy light.
Secure the occupancy light (E053) to the frame with the provided screws.
Parts used:
occupancy light | E053 | 2×
3×30 mm screw | T0136 | 2×
Door adjustment
48. Adjust the door
Check the door adjustment in the video.
Hinge Cover
49. Install Hinge Cover
Place the hinge covers over the hinges on the door frame as shown.
Secure each cover with screws
Parts used:
hinge cover | not labeled | 6×
M4×10 mm screw | T0310 | 12×
Ledge
50. Install Ledge
Apply double-sided tape along the back of the ledge (K0493).
Stick the ledge to the indicated position on the frame.
Parts used:
ledge | K0480 | 1×
double-sided tape
Cord Connection
51. Connect the Power Supply Cord to Powerbox
Plug the power cord into the powerbox as shown in the detail view.
Ensure the connection is secure.
52. Install the Revision Door
Position the cover (K0487) over the power cord and secure it in place.
Parts used:
Cord cover | K0487 | 1×
53. Attach the Lower Interior Panel to the Dock
Place the internal panel (7.1-SUG4) over the power cord section and secure in position.
Parts used:
lower interior panel | 7.1-SP, CH2G4 | 1×
Initial Setup
54. Initial Setup
Following assembly, authorized personnel must perform a mandatory initial setup for all GEN4 products. This involves accessing the display settings to configure key parameters, such as the pod model, language, and time synchronization, to ensure all components function correctly.
