Rattan Corner Set with Composite Table

This guide provides step-by-step instructions for assembling, operating, and maintaining your Rattan Corner Set with Composite Table.

Product Information

Rattan Corner Set with Composite Table

SKU: 216735,216737

Table Dimensions	700 x 1200 x 660 mm
L Shaped Sofa Dimensions	1800 x 2400 x 700 mm
Stool Dimensions	400 x 400 x 330 mm
Seat Cushion Thickness	80 mm
Back Cushion Thickness	130 mm

GPSR Information

Manufacturer: Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG
Person Responsible: Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England, +441347878880

Manufacturer: Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands +441347878880
Person Responsible: Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands, +44134787888

Safety Advice

Ensure you have read and fully understood the instruction manual and safety advice before using this product.

Carefully inspect all parts before assembly to ensure no components are damaged or missing. Do not attempt to use or assemble the product if any part is cracked, broken, or missing.
Assemble the product on a flat, clean surface to prevent instability or incorrect fitting. Ensure all fixings are tightened fully and checked regularly for loosening over time.
Ensure all modular sections are securely fastened together according to the instructions to reduce the risk of pinch points or separation during use.
Use caution when moving or rearranging modular sections. Do not place fingers near connecting joints to avoid pinch injuries.
Do not allow children to climb or play on the furniture to avoid tipping, falling, or other injuries.
Place furniture in a well-lit area to ensure clear visibility of corners and low stools, reducing tripping hazards.
Always tuck stools under the table when not in use to prevent accidental trips or falls.
Be cautious when walking around the corner sections and low-height seating components, particularly in low lighting.
Ensure all cushions are correctly positioned and secured before use. Sit down slowly and gently to avoid dislodging cushions or destabilising the seating.
Do not stand on any part of the furniture or use it for anything other than its intended domestic seating and dining purposes.
Do not exceed the recommended weight limit of 150kg (approx. 330lbs) per seat. Doing so may cause structural damage or personal injury.
Regularly inspect the tabletop for sharp edges, splinters, or surface damage. Avoid dragging objects across the surface and clean with a soft cloth to maintain condition and reduce risk of injury.
The composite polywood tabletop is impact-resistant but not shatterproof – do not drop heavy items or strike the surface forcefully.
Avoid placing hot items directly onto the composite table as this may cause warping or discolouration. Always use heat-resistant mats or coasters.
Ensure the product is used on stable, even ground. Uneven surfaces may cause wobbling, instability, or damage to frame connections.
Do not place the product near open flames, heaters, or other ignition sources. The synthetic rattan and polywood materials are flammable if exposed to extreme heat.
Store cushions indoors or in a waterproof cushion box when not in use to prevent mould, mildew, or UV degradation. Ensure cushions are dry before storing.
Individuals with fabric allergies or skin sensitivities should verify the cushion materials before use. Use personal covers or alternative cushions if required.
Clean the furniture regularly with mild soap and water. Avoid harsh chemicals or pressure washers, as these may damage the rattan finish or weaken structural joints.
Do not allow the product to become waterlogged. While the materials are weather-resistant, prolonged exposure to moisture may cause frame corrosion or rattan degradation.
During high winds or storms, move the furniture to a sheltered area or secure it to prevent movement or tipping.
Inspect all frame joints, fixings, and connecting brackets at regular intervals. Retighten or replace any loosened components immediately.
This product is intended for outdoor domestic use only. Do not use in commercial settings unless specifically rated for such environments.

Materials

Sofa Assembly
1. Step 1 - Sofa Assembly
Using the screws and washers (Part X), attach the left side back seat panel (Part N), the left side front panel (Part R), the base seat side panel (Part P) and the right side arm rest (Part I) together.

Note: Make sure the holes are lined up evenly before tightening the screws.
2. Step 2 - Sofa Assembly
Using the screws and washers (Parts X and Y), assemble together the base seat side panel (Part P), the right side back seat panel (Part M), the right side front panel (Part Q), the left side arm rest (Part J), and the right side base seat panel (Part L).

Notice: Make the holes are lined up correctly before tightening the screws.
3. Step 3 - Sofa Assembly
Using the screws and washers (Parts X and Y) assemble together the base seat side panel (Part P), the short corner back seat panel (Part O), the long corner back seat panel (Part M1), the right side front panel (Part Q) and the right side base seat panel (Part L).

Note: Make sure the holes are lined up correctly before tightening the screws.
4. Step 4 - Sofa Assembly
Using the screws and washers (Part X), install all of feet (Part V) to the bottom of the sofa frame.

Note: Make sure everything is lined up correctly before tightening the screws.
5. Step 6 - Sofa Assembly
Install the back seat cushions (Part T), the back corner cushion (Part U), the base seat cushions (Part S) and the stool cushions (Part H).

Note: Make sure the sofa and stool is secure before placing the cushions.
Table Assembly
6. Step 1 - Attach the Table Legs to the Connector
Place the two table legs (Part B) upright and facing each other.

Position the table leg connector (Part C) between the frames, aligning the holes.

Insert a bolt (Part W) with a washer (Part Y) through each hole.

Tighten the bolts using the allen key (Part Z).

Do not fully tighten until all bolts are in place.

Note: Make sure the support bar is level before moving to the next step.
7. Step 2 - Attach Tabletop to the Legs
Place the tabletop (Part A) upside down on a soft, flat surface.

Position the assembled legs and connector on top of the tabletop. Align all holes.

Place a washer (Part Y) onto each bolt (Part X).

Insert bolts through the frame brackets into the tabletop holes.

Tighten using the allen key (Part Z).

Tighten all bolts securely once they are all inserted.

Note: Make sure the frame is centred and straight before fully tightening.
Stool Assembly
8. Part 1 - Stool Assembly
Using the screws and washes (Part X), assemble the stool together by lining up the legs (Part F) and the side panels (Part G).

Once Parts F and G are assembled, use Part X to install the stool top (Part E).
Troubleshooting
9. Maintenance
This maintenance guidance supports safe, long-term use of your rattan corner sofa set and helps ensure continued compliance with safety expectations under the General Product Safety Regulation (GPSR).

Routine Cleaning

Clean the synthetic rattan frame regularly using a soft brush or cloth and warm water with mild detergent.

Do not use abrasive cleaners, scouring pads, solvent-based products, bleach, or pressure washers, as these may weaken the rattan weave and protective coatings.

Wipe the composite table top with a damp cloth after use and dry thoroughly to prevent surface marks or moisture retention.

Avoid dragging sharp or heavy objects across the table surface to reduce risk of scratching or structural weakening, in line with identified impact risks .

Cushion Care

Remove and shake out cushions regularly to prevent dust build-up.

Clean cushion covers in accordance with their care label instructions. Do not exceed recommended washing temperatures.

Ensure cushions are completely dry before placing back on the furniture to prevent mould growth and material degradation.

Inspect cushions for wear, thinning fabric, or loose stitching, and replace if deterioration is identified to reduce slipping or instability risks .

Store cushions indoors in a dry, ventilated space when not in use or during prolonged wet weather.

Structural Inspection

Periodically inspect the rattan weave for fraying, cracking, or separation, particularly at corners and load-bearing points.

Check all joints between modular sections to ensure connectors remain secure and aligned to minimise pinch point risks .

Inspect the table top for chips, cracks, rough edges, or splintering before use. If damage is identified, discontinue use until repaired or replaced .

Ensure all feet remain stable and level; adjust positioning if movement or wobbling occurs to prevent tipping or tripping hazards .

Environmental Protection

Although designed for outdoor use, prolonged exposure to extreme weather (heavy rain, frost, intense UV, or snow) may reduce product lifespan. Use a breathable, correctly fitted furniture cover when not in use.

Do not cover furniture while damp; allow it to dry fully before fitting protective covers.

In winter months or severe weather conditions, store the set in a sheltered, dry location where possible.

Safe Handling During Maintenance

When moving modular sections for cleaning, lift rather than drag to prevent frame stress and reduce risk of joint separation .

Take care to avoid placing fingers between sections while repositioning to prevent pinch injuries .

Ensure stools are returned neatly under the table after cleaning to minimise trip hazards .

Long-Term Care

Avoid standing or placing excessive point loads on the table surface.

Rotate seating positions periodically to ensure even wear distribution.

Replace any damaged components only with manufacturer-approved parts to maintain structural integrity and safety compliance.

If significant structural damage, instability, or material degradation is observed, discontinue use immediately and contact the manufacturer or authorised supplier for guidance.
10.

Please read through the guide below if you have any issues or faults with your device. The information covers and resolves the majority of frequently asked questions.

Q: There are parts missing from my order. A: If there appears to be any part missing from your package contact our Customer Support team via the details on the Contact Us page within 7 days of receipt.

For all other issues please contact our Customer Support department via the details on the Contact page.